FAQ - Frequently Asked Questions
Before ordering
- The goods are shipped after your payment has been received, provided that the order or parts of it are not on backorder.
- When the goods are shipped you will receive an e-mail notification with the Hermes or DHL tracking number.
- You can track your shipment online at www.myhermes.de or www.dhl.de.
- Our bright zinc-plated sleeves have no problems with corrosion or rust if the bushes are lubricated correctly during installation (re-greasing is not necessary!). After the sleeve is pressed in, the grease collects in the honeycomb structure in the bore of the bush. Because the sleeve is pressed in tightly, no water or dirt can get between sleeve and bush, so no rust can form.
- When the control arm pivots, the bush turns together with the arm around the sleeve. Bright zinc-plated sleeves have a lower coefficient of friction than stainless steel sleeves, which lets the arm pivot more freely.
- For more than 30 years we have only offered bright zinc-plated sleeves and have never had any problems with them.
Either your authorised dealer can help you if you give them the chassis number, or you can measure the anti-roll bar with a calliper. Measure directly next to the original rubber, as on some vehicles the anti-roll bars taper towards the outside!
If the vehicle is very old (around 20 years), it is rather unlikely that bushes will still be developed for it. If it is a newer vehicle model, there is a good chance that bushes will become available in the near future. Custom manufacture to size is very time-consuming and costly, so we do not offer it.
We guarantee that all Whiteline bushes deliver a very good result in terms of handling, driving behaviour etc. The hardness of the bushes is optimally tuned for both everyday road use and track driving. In some cases we even offer bushes with a harder compound, which are therefore mainly suited to motorsport. Where these are available for your vehicle, they are also listed in the shop.
Order
After ordering
First of all, the old rubber mounts have to be removed. A press with a suitable adapter can be used to press out the old bushes. If no press is available, the old rubber can also be burnt out with a gas torch or similar and the old metal shell knocked out with a chisel (if necessary saw into it beforehand with a fret saw - but be careful: do not damage the control arm!!). The seat then has to be cleaned of rust with sandpaper and cleaned.
All Whiteline Performance bushes can now be fitted with normal tools. Usually all you need is a vice, but we recommend using a workshop press. Another option is a threaded rod fitted with a nut and a large washer. This is passed through the sleeve of the bush and pressed into the seat from above with another nut and washer.
Every kit also includes a special lubricant (if required) that allows straightforward installation. Please use only the enclosed lubricant. Other lubricants are not suitable and will void the warranty and guarantee!
After installation, please tighten all bolts to the torque specified by the vehicle manufacturer. Please note that installation should be left to qualified personnel only. We are not liable for any damage caused by incorrect installation!
In addition, a wheel alignment and adjustment should be carried out after changing control arm bushes.
Special case: on vehicles that are extremely low, our adjustable drop links can be used for more clearance. However, this always has to be tested on the vehicle itself, depending on the components fitted. If necessary, the drop links may have to be ordered one size shorter. You should measure this on the vehicle beforehand. An overview of all lengths can be found in the catalogue under vehicle manufacturer "- Universal -".
Yes, Whiteline bushes give you significantly better handling than rubber bushes. Fitting Whiteline bushes is especially recommended if the vehicle is used both on the track and on the road, as nylon bushes or solid components are unsuitable for road use.
- Photos of the defective parts
- Our article numbers of the defective part(s)
- Vehicle data: type, year of manufacture, engine
- How long have the parts been fitted (approx. km and time)?
- Does the defect affect the parts on both sides? If not, which side is affected?
- What has been changed on the vehicle?
- Changes to the suspension?
- Changes to the engine?
- In motorsport: are slicks or semi-slicks used?
- Is a modified brake system used?
- How was the vehicle driven: track/off-road or road?
- If track: which track is it?
- For adjustable drop links: were they set to the original length?
For further information on withdrawing from an order, please read our General Terms and Conditions.
About our products
The transparent Whiteline grease was developed specifically for use with Whiteline polyurethane material and is silicone-based, which protects the grease against drying out and thus ensures a long service life of the bush. The helical knurling in the bore of the bush also ensures that the grease stays there and lubrication is ensured for a long time. In contrast to common lubricants such as copper paste, Whiteline grease lasts considerably longer without drying out. Especially with copper paste it very often happens that the bushes have to be re-greased, because noise is caused by direct friction between metal and polyurethane.
These bushes have an eccentric bore instead of a centred one. If the eccentric bore is oriented towards the ground when the bush is pressed in, the suspension geometry on the front axle can be changed so that traction noticeably increases during fast acceleration. This is achieved by moving the mount of the lower control arm slightly downwards (through an eccentric bore in the bush). Among other things this reduces body rocking/squatting of the rear axle during fast acceleration (known as anti-lift) and increases front-axle dive under heavy braking, which noticeably increases grip in both situations because more weight stays on the front axle.
Alternatively this set can be used to create more positive caster, which among other things improves cornering because the vehicle starts to understeer later (i.e. slides wide over the front axle) and can therefore be driven at a higher cornering speed.
Depending on how the eccentric bush is pressed in, either caster can be increased or the anti-lift setting can be used. This is described in the enclosed instructions with text and drawings. If you have any questions about installation, we are also happy to help.
Yes. The polyurethane compounds used for Whiteline bushes stay flexible even at very cold temperatures. However, if the vehicle is used for a long time at temperatures below -40 degrees Celsius, bushes with a softer material hardness should be used. Whiteline products have already been successfully tested in the Antarctic, the northern Arctic Circle and in Northern and Eastern Europe.
So-called offset bushes have an eccentric bore in the pin or in the bush itself. This allows the caster or camber of the vehicle (depending on the type of suspension) to be changed by pressing the bush in at a specific position (illustrated installation instructions are enclosed, and we are also happy to help with installation). The adjustment range is not continuous; the bore specifies a fixed value. Depending on the position of the eccentric bore when pressing in, camber/caster can be influenced in a + or - direction. For caster a more positive value is naturally recommended; for camber either positive or negative, depending on whether you want more negative camber to improve cornering behaviour or want to correct an excessively negative camber value (e.g. due to extreme lowering) back towards positive to avoid one-sided tyre wear.
Yes, by fitting Whiteline polyurethane bushes you will notice a clear difference compared with rubber bushes. The steering becomes considerably more precise and handling in extreme situations is also improved. In addition, tyre life is significantly longer because traction increases.
With normal use you can assume that they last about 5 to 6 times longer than normal rubber bushes. The insensitivity to water, oil, ultraviolet light and road salt in particular makes polyurethane bushes very durable. What matters here is that sufficient lubrication is ensured. Please use only the supplied special grease, which is optimally matched to the properties of the Whiteline polyurethane material and thus ensures a long service life.
No matching question found.

